Wireless Bridge,5.8G Outdoor Point to Point Access PTMP WiFi PTP Network 300Mbps CPE 3KM Transmission Distance 14DBi High-Gain Antenna 24V PoE Power Supply 2 Pack

$109.99
In stock
SKU
CPE335
  • 5.8Ghz / 300Mbps Transmission: the wireless bridges use 5.8ghz 300Mbps technology and 14DBI high-gain antenna with maximum transmission range up to 3km / 1.86 miles(Barrier-free), with 100Mbps network LAN port, can provide up to 100Mbps wired network speed, suite for two building(point to point) internet network access sharing, remote IP camera video surveillance, or remote network WiFi access.
  • PTMP Pre-programmed: simply connect the both bridges to PoE adapters through the ethernet cables, system will power on, and wait for 1 minute for the both equipment to pairing and connect together, the "Link" green LED indicator will turn on to indicate that the both bridges have been paired succeeded. Great for extend the internet to your garage, barn, store, and warehouse through 5.8Ghz wireless transmission, instead of complicated wire connection.
  • Long Range & High Speed: the wireless bridges work in 5.8Ghz with 300Mbps wireless transmission rate, support 3km / 1.86 miles transmission distance(Barrier-free), provide up to 100Mbps wired network speed, extend the networks from one building to another even more, suitable for share internet access, video camera surveillance, or remote network WiFi hot point access (AP mode).
  • Point to Point Mode: Connect the both wireless bridges to the PoE power adapter will auto pair, no need connect to computer for the complicated configures, at point-to-point mdoe can use for long range video surveillance and internet network sharing, the master bridge output WiFi hot point, you can enter password to get access, extend the WiFi access coverage up to 3km / 1.86 miles in 60 a degree angle of the front direction.
  • Point to Multiple Point Mode: suit for the video surveillance DVR system to receives the IP cameras video stream for different building or place, the master bridge connects to the DVR system, and the slave bridges connects to the IP cameras, in this way you can management different building's IP cameras in one system without wiring, you have to connect to computer to configure the master and slave bridge which need some internet knowledge.
 

CPE335 Outdoor Wireless Bridge Kits

wireless bridge cpe 335

CPE335 5.8G Wireless Bridge with 300Mbps and 1.86 Miles Data Transfer Range

CPE335 wireless bridge kits is one pair of outdoor high power and high performance 300Mbps wireless bridges, which works at 5GHz frequency. Supports Point-to-Point and Point-to-Multipoint wireless connection. It is more stable and higher speed and anti-interference performance than 2.4GHz wireless bridge. Moreover, it is easy to manage through the WEB interface.

CPE335 Kits Function:

A. the device can works as Auto pairing mode: simply to use, connect both bridges to the PoE power adapter to start working, it will auto pair in few minutes. Customize mode: need connect the bridges to the computer through ethernet cable, and configure the master & slave parameters, this mode suit for experienced technician.

B. the device can use for share internet networks to a long distance, output WiFi hot point, also can use for transmit the long ranges IP cameras' video stream to the control center without complicated wiring connection.

C. Auto pairing mode works for point-to-point access connection, customize mode can configure the point to multiple point connection.

CPE355 Kits Application:

The CPE335 kits is great to extend your home internet network to another building without wire connection, you can share your network to your barn garage, warehouse, workshop or small store near to your home, it also works for enterprise to share the internet from different office, workshop, warehouse and etc.

We offer a pair of wireless bridge in the package, we need to set one works as master mode, and another works as slave mode.

Wireless Bridge Master & Slave Set:

1.Master Bridge Set

Move the mode switch to "A" position, the device works as master mode

2.Slave Bridge Set

Move the mode switch to "B" position, the device works as slave mode

Share your internet network from one building to another without complicated wire connection

access point

Extend your internet network to another building without wire connection, works as outdoor wireless access point

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the router through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the computer or router by another ethernet cable

The master bridge transfer data to slave bridge works as point to point mode to extend network access to another house, office, building for internet surfing. The master bridge also output WiFi hot point, such as outdoor access point, you can open the WiFi connection setting on your cellphone, or laptop, you will find the WiFI name CPE5G_5Gxxx, enter the password to get access.

The access password is pre-programmed, it is different depend on what channel the wireless bridge working, but only change the last two or three numbers.

For example: the WiFi hot point name is CPE5G_5G161, and the default password is zllinkcpe123456161, if the name is CPE5G_5G153, the password will be zllinkcpe123456153, the last three numbers of the password is match to the last three numbers of the name, zllinkcpe123456 is the same, you can find the password with a little bit change for different channel.

Point to point video surveillance connection disgram

wireless bridge video surveillance

Transfer the video stream from the slave bridge to the master bridge, DVR receive & manage the video stream

Wireless Bridge Master & Slave Set:

1.Master Bridge Set

Move the mode switch to "A" position, the device works as master mode

2.Slave Bridge Set

Move the mode switch to "B" position, the device works as slave mode

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the switch by another ethernet cable

Point to Point video surveillance, expand your video surveillance range, easily management all your surveillance camera in one DVR system without complicated wiring. Transfer your video surveillance network IP cameras data from another building to your DVR, easy to management all the cameras in one system.

Point to multiple point video surveillance connection diagram

point to multiple point access

One master bridge and multiple slave bridge connection together by computer configure to management different place's IP cameras to one DVR system

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the IP cameras by another ethernet cable

Install the slave bridges face to face to the master bridge, and the direction angle no more than 60 degrees, this connection need login into computer to configure the IP address for different slave, please read the user manual for details.

In this way, you can easy transfer the network camera video streaming from different buildings to the DVR of the control center, point to multiple point function is great for you to monitoring multiple buildings without complicated wiring.

CPE335 Product Interface

wireless bridge interface

The wireless bridges work by two modes, auto pairing mode with pre-programed suit for newbie, customize mode suit for experienced user.

Auto pairing mode:

connect it to the PoE power adapter, the Power LED turns green on, system is power on, when the both bridges all are power on, it will auto pair in few minutes, the pairing and LAN status LED light all turns green on. the digital LED indictor display the numeric in red color.

you can press the "RST" button to change the channel to find a good frequency without interference, short press the button, the LED indicator will display the numeric "0","1","2","3"..."F" one by one, and change in cycle, each numeric means a different frequency, you can find the details on the user manual.

Customize mode:

at this mode you need connect it to computer and set the different IP address and working mode, short press the "RST" button will not functional at this mode, but you can press and hold this button over 10 seconds to reset to factory mode.

Parameters

Model: CPE335
Network Interface: 10/100Mbps 2 * LAN Port
Data Rate: 11a: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps / 11n: 7.2M, 14.4M, 21.7M, 28.9M, 43.3M, 57.8M, 65M, 72.2M, 14.4M, 28.9M, 43.3M, 57.8M, 86.7M, 115.6M, 130M, 144.4Mbps
Power Supply: POE 24V 1.0A
Antenna: 14DBi (5180~5825MHz)
Transmission Range 3KM / 1.86 miles
Waterproof: IP65
Dust-proof: Support
Working temperature: -4℉~158℉
Dimensions: 250mm * 90mm * 65mm / 9.8'' * 3.55'' * 2.56''
Weight 1.1kg / 38.8 oz (A pair)
Write Your Own Review
You're reviewing:Wireless Bridge,5.8G Outdoor Point to Point Access PTMP WiFi PTP Network 300Mbps CPE 3KM Transmission Distance 14DBi High-Gain Antenna 24V PoE Power Supply 2 Pack
Your Rating
© 2021 Wondcam.com. All Rights Reserved.